.MA3 LDX #0 \ We're about to work our way through all the ships in \ our local bubble of universe, so set a counter in X, \ starting from 0, to refer to each ship slot in turn .MAL1 STX XSAV \ Store the current slot number in XSAV LDA FRIN,X \ Fetch the contents of this slot into A. If it is 0 BNE P%+5 \ then this slot is empty and we have no more ships to JMP MA18 \ process, so jump to MA18 below, otherwise A contains \ the type of ship that's in this slot, so skip over the \ JMP MA18 instruction and keep going STA TYPE \ Store the ship type in TYPE JSR GINF \ Call GINF to fetch the address of the ship data block \ for the ship in slot X and store it in INF. The data \ block is in the K% workspace, which is where all the \ ship data blocks are stored \ Next we want to copy the ship data block from INF to \ the zero-page workspace at INWK, so we can process it \ more efficiently LDY #NI%-1 \ There are NI% bytes in each ship data block (and in \ the INWK workspace, so we set a counter in Y so we can \ loop through them .MAL2 LDA (INF),Y \ Load the Y-th byte of INF and store it in the Y-th STA INWK,Y \ byte of INWK DEY \ Decrement the loop counter BPL MAL2 \ Loop back for the next byte until we have copied the \ last byte from INF to INWK LDA TYPE \ If the ship type is negative then this indicates a BMI MA21 \ planet or sun, so jump down to MA21, as the next bit \ sets up a pointer to the ship blueprint, and then \ checks for energy bomb damage, and neither of these \ apply to planets and suns ASL A \ Set Y = ship type * 2 TAY LDA XX21-2,Y \ The ship blueprints at XX21 start with a lookup STA XX0 \ table that points to the individual ship blueprints, \ so this fetches the low byte of this particular ship \ type's blueprint and stores it in XX0 LDA XX21-1,Y \ Fetch the high byte of this particular ship type's STA XX0+1 \ blueprint and store it in XX0+1Name: Main flight loop (Part 4 of 16) [Show more] Type: Subroutine Category: Main loop Summary: For each nearby ship: Copy the ship's data block from K% to the zero-page workspace at INWK Deep dive: Program flow of the main game loop Ship data blocksContext: See this subroutine in context in the source code Variations: See code variations for this subroutine in the different versions References: This subroutine is called as follows: * KS1 calls via MAL1 * Main flight loop (Part 12 of 16) calls via MAL1
The main flight loop covers most of the flight-specific aspects of Elite. This section covers the following: * Start looping through all the ships in the local bubble, and for each one: * Copy the ship's data block from K% to INWK * Set XX0 to point to the ship's blueprint (if this is a ship)
Other entry points: MAL1 Marks the beginning of the ship analysis loop, so we can jump back here from part 12 of the main flight loop to work our way through each ship in the local bubble. We also jump back here when a ship is removed from the bubble, so we can continue processing from the next ship
[X]
Subroutine GINF (category: Universe)
Fetch the address of a ship's data block into INF
[X]
Label MA18 in subroutine Main flight loop (Part 13 of 16)
[X]
Label MA21 in subroutine Main flight loop (Part 6 of 16)
[X]
Label MAL2 is local to this routine
[X]
Configuration variable NI% = 36
The number of bytes in each ship's data block (as stored in INWK and K%)
[X]
Temporary storage, used to store the address of a ship blueprint. For example, it is used when we add a new ship to the local bubble in routine NWSHP, and it contains the address of the current ship's blueprint as we loop through all the nearby ships in the main flight loop
[X]
Variable XX21 (category: Drawing ships)
Ship blueprints lookup table